Pozna kdo te felge?
Pozna kdo te felge?
So mi vsec pa rabim ceno za 17"
Link kjer se prodajajo pod imenom Smoor: http://www.smoor-felgen.de/pagea.html
V kotu pa pise da jih izdeluje MB Italia kar pa tudi ne poznam, bi se pa verjetno dalo direktno to zelo ugodno dobit
thx
Link kjer se prodajajo pod imenom Smoor: http://www.smoor-felgen.de/pagea.html
V kotu pa pise da jih izdeluje MB Italia kar pa tudi ne poznam, bi se pa verjetno dalo direktno to zelo ugodno dobit
thx
Koncno so stran usposobili in se da vse videt.
http://www.meccanicabrembana.it/pdf/011_7x17.pdf
Ma kdo link do clanka kaj pomenijo mere pri felgah? J, ET, offset ipd.
thx
http://www.meccanicabrembana.it/pdf/011_7x17.pdf
Ma kdo link do clanka kaj pomenijo mere pri felgah? J, ET, offset ipd.
thx
...odvisno katere želiš? ...nočem delat reklame, vendar verjami da se da dobit tuki; recimo prav te Smoor,lahko pridejo naslednji teden, če so na lagerju v Nemčiji (ne me držat za besedo glede datuma)CupraR napisal/-a:In kje se da to pri nas dobit Že lep cajat razmišlam da bi se šlo v Nemčijo po kkšne feltne.
lp
Tomas
Tomas
..naj me kdo popravi če se motim...Malecky napisal/-a:Koncno so stran usposobili in se da vse videt.
http://www.meccanicabrembana.it/pdf/011_7x17.pdf
Ma kdo link do clanka kaj pomenijo mere pri felgah? J, ET, offset ipd.
thx
J je širina feltne (jod);
ET ali offset je razdalje od "peste" do centra feltne; lahko je pozitiven ali negativen;
PCD je razmak med vijaki;
itd...
Veliko je pa napisanega tudi na netu, tako da najdeš tam vse...
lp
Tomas
Tomas
- Pugi
- N2O addiction team founder
- Prispevkov: 2148
- Pridružen: 07 Okt 2004, 13:06
- Kraj: Turbolandija
- Kontakt:
Prosem če nehate govort jodov širine, ker sploh ne vem od kje folku to. J je oznaka za Obliko feltne, 7.5 pa pomeni širino feltne v inchih=2.54cm.
Maja - a si kdaj gledala od Toore feltne, oni majo vse mogoče mere, tud 7J18
Maja - a si kdaj gledala od Toore feltne, oni majo vse mogoče mere, tud 7J18
1 hors v gobec pa 300 pod haubo, pa maš rešen. Večje, k sta obe številke, bolj maš rešen.
- Pugi
- N2O addiction team founder
- Prispevkov: 2148
- Pridružen: 07 Okt 2004, 13:06
- Kraj: Turbolandija
- Kontakt:
The wheel offset defines the distance of the flange from the centre of the wheel mouth in millimetres. If the offset is zero, the flange is located exactly in the centre of the wheel, and the wheel extends exactly as far outwards as inwards. For example, a 9 inch width wheel with an offset of zero extends 11.43 cm outwards and 11.43 cm inwards. A positive offset (e.g. +25) indicates that the wheel extends further inwards (towards the centre of the vehicle) than outwards (towards the wing housing).
Starting from zero, the track would become narrower by 25 mm. A negative offset (e.g. -25) would mean that the wheel extends outwards and the track would be wider (again by 25 mm starting from zero). If we therefore had two pairs of wheels of equal width to choose from, one having an offset of plus 25 mm and the other minus 25 mm, we could make the track 5 cm wider on each side by fitting the pair with the negative offset rather than the other pair. In total the track would be 10 cm wider than with the "positive offset" wheels.
Starting from zero, the track would become narrower by 25 mm. A negative offset (e.g. -25) would mean that the wheel extends outwards and the track would be wider (again by 25 mm starting from zero). If we therefore had two pairs of wheels of equal width to choose from, one having an offset of plus 25 mm and the other minus 25 mm, we could make the track 5 cm wider on each side by fitting the pair with the negative offset rather than the other pair. In total the track would be 10 cm wider than with the "positive offset" wheels.
1 hors v gobec pa 300 pod haubo, pa maš rešen. Večje, k sta obe številke, bolj maš rešen.